valego Posted August 22, 2007 Share Posted August 22, 2007 CPU # LGA 775 socket for: - Intel® CoreTM2 Quad, Intel® CoreTM2 Extreme, Intel® CoreTM2 Duo, Intel® Pentium® D or Intel® Pentium® 4 # Supports Intel Enhanced Memory 64 Technology (EMT64T) # Supports Enhanced Intel SpeedStep Technology (EIST) # Supports Intel Hyper-Threading Technology # Supports 1333*/1066/800MHz system bus speed *Available only on CPUs that support 1333MHz FSB Chipset # Intel® chipset - Northbridge: Intel® P35 Express chipset (with Intel® Fast Memory Access technology) - Southbridge: Intel® ICH9R Memory # Four 240-pin DDR2 DIMM sockets # Supports DDR2 667/800 MHz # Delivers up to 12.8Gb/s bandwidth # Supports dual channel (128-bit wide) memory interface # Supports up to 8GB system memory # Supports unbuffered x8 and x16 DIMMs BIOS # Award BIOS # 8Mbit flash memory Power Management # ACPI and OS Directed Power Management # ACPI STR (Suspend to RAM) function # Wake-On-PS/2 Keyboard/Mouse # Wake-On-USB Keyboard/Mouse # Wake-On-LAN and Wake-On-Ring # RTC timer to power-on the system # AC power failure recovery Hardware Monitor # Monitors CPU/system/Northbridge temperature and overheat alarm # Monitors Vcore/Vdimm/Vnb/VCC5/12V/V5sb/Vbat voltages # Monitors the speed of the cooling fans # CPU Overheat Protection function monitors CPU temperature and fan during system boot-up - automatic shutdown upon system overheat Storage # Intel ICH9R chip - Intel Matrix Storage technology - Supports up to 6 SATA devices - SATA speed up to 3Gb/s - RAID 0, RAID 1, RAID 0+1 and RAID 5 # JMicron JMB363 PCI Express to SATA and PATA host controller - Supports up to 2 UltraDMA 100Mbps IDE devices - Supports 2 SATA devices - SATA speed up to 3Gb/s - RAID 0 and RAID 1 Audio # Bernstein audio module - Realtek ALC885 8-channel High Definition Audio CODEC - Center/subwoofer, rear R/L and side R/L jacks - Line-in, line-out (front R/L) and mic-in jacks - 2 coaxial RCA S/PDIF-in/out jacks - 1 optical S/PDIF connector - 1 CD-in connector - 1 front audio connector # DAC SNR/ADC SNR of 106dB/101dB # Full-rate lossless content protection technology LAN # Marvell 88E8052 and Marvell 88E8053 PCIE Gigabit LAN controllers # Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) and 802.3ab (1000BASE-T) standards IEEE 1394 # VIA VT6307 # Supports two 100/200/400 Mb/sec ports I/O Connectors # 3 connectors for 6 additional external USB 2.0 ports # 1 connector for an external COM port # 1 connector for an IEEE 1394 port # 1 connector for the Bernstein audio module # 1 front audio connector (on the Bernstein audio module) # 1 CD-in connector (on the Bernstein audio module) # 1 S/PDIF connector (on the Bernstein audio module) # 1 IrDA connector # 1 CIR connector # 8 Serial ATA connectors # 1 40-pin IDE connector # 1 floppy connector # 1 24-pin ATX power connector # 1 8-pin 12V power connector # 2 4-pin 5V/12V power connectors (FDD type) # 1 front panel connector # 6 fan connectors # 1 diagnostic LED # EZ touch switches (power switch and reset switch) Rear Panel I/O Ports # 1 mini-DIN-6 PS/2 mouse port # 1 mini-DIN-6 PS/2 keyboard port # 1 IEEE 1394 port # 6 USB 2.0/1.1 ports # 2 RJ45 LAN ports Expansion Slots # 3 PCI Express x16 slots (PCIE1 at x16, PCIE3 at x4 or x1 and PCIE4 at x1) # 1 PCI Express x1 slot # 3 PCI slots PCB # 6 layers, ATX form factor # 24.4cm (9.6") x 30.5cm (12") Link al sito DFI: LANPARTY UT P35-T2R Quote Link to comment Share on other sites More sharing options...
valego Posted August 22, 2007 Author Share Posted August 22, 2007 Download Bios Ufficiali 913 - Enhance data transmitting added turbo. - Fixed cdrom name error in setup. - Added CMD Tfine control Tfine Item. - Added Tras 1~8. - Added T2 Dispatch item. - Change Read delay phase adjust item config. Remark :This new update BIOS(2007/09/13) comes with some new features such as “T2 Dispatch , CMD Tfine Control and Tras 1~8”, therefore the existing CMOS Reloaded setting stored on your motherboard cannot apply to this new update BIOS. Users will need to manually set your overclock setting to this update BIOS and save those setting in CMOS Reloaded to work with this new update BIOS. 823 - Added LAN, Audio,1394, IDE chip Item. - Support DDR2 533 Module when NB strap jump set to 333MHz. - Fixed can't install vista when plus 4GB memory. - Fixed Vista64 DRAM size issue. - Fixed EIST can't be disabled in vista. - Fixed can't boot from SATA CD-ROM when Enable RAID mode.. 815 - Added LAN, Audio,1394, IDE chip Item. - Support DDR2 533 Module when NB strap jump set to 333MHz. - Fixed can't install vista when plus 4GB memory. - Fixed Vista64 DRAM size issue. - Fixed vista64 DRAM size issue. - Fixed EIST can't be disabled in vista. 727 -Release iniziale Beta 810 BETA - Added LAN, Audio,1394, IDE chip Item. - Support DDR2 533 Module when NB strap jump set to 333MHz. - Fixed can't install vista when plus 4GB memory. - Fixed Vista64 DRAM size issue. 815 BETA - Fixed vista64 DRAM size issue. - Fixed EIST can't be disabled in vista. 817 BETA 823 BETA Beta Mod 0913 Mod Beta Ricordatevi prima di flashare di caricare il settaggi default tramite il bios e non flashare con sistema overclockato. Poi meglio se fatte l'aggiornamente tramite DOS. Una volta flashato si consiglia da Oscar (autore di questo bios) di togliere la batteria per circa 5 min Ultima cosa flashate a vostro rischio. Ricordo e un bios mod beta non ancora rilasciato. Da ieri,15/09/2007 che lo usano e nessuno si lamenta di problemi, anzi va meglio e ci sono voci che risulta problemi con le ram gkx e alcuni ali della enermax Driver Audio Driver 2007/07/31 LPP35_Audio.zip Descrizione: Audio Driver for P35 series under Windows XP / Vista 32bits/64bits. RAID Driver 2007/07/31 ICH9R_RAID_Fpy.zip Descrizione: RAID Driver for ICH9R of P35 series under Windows XP, Vista 32/64bits. Intel INF Utility 2007/07/31 Intel_Inf_Util.zip Descrizione: Intel chipset driver for P35 series under Windows XP 32/64bits , Vista 32/64bits. RAID Driver 2007/07/31 JMicron_RAID.zip Descrizione: RAID Driver for JMicron Chipset of LP UT P35-T2R under Windows XP, Vista 32/64bits. Smart I/O Driver 2007/07/31 LPP35_SG.ZIP Descrizione: ITE Smart Guareian for Infinity P965-S under Windows XP , Vista 32/64bits. LAN Drivers 2007/07/31 LPP35_Marvell_LAN.zip Descrizione: LAN Driver for P35 series under Windows XP/Vista 32/64bits. RAID Driver 2007/07/31 JMicron_RAID_Fpy.zip Descrizione: RAID Driver for JMicron ChipSet of LP UT P35-T2R under Windows XP, Vista 32/64bits. Utility 2007/05/03 net2_32.exe Descrizione: Microsoft.Net Framework 2.0 utility for Windows XP 32Bits, Windows Vista 32Bits. 2007/05/03 net2_64.exe Descizione: Microsoft .Net Framework 2.0 utility for Windows XP 64Bits , Windows Vista 64Bits. Manuali English/Multilingual Manual PROGRAMMI UTILI setfsb20b15n.zip selezionare Clock generetor CY28551LFXC Quote Link to comment Share on other sites More sharing options...
valego Posted August 22, 2007 Author Share Posted August 22, 2007 Consigli Per eliminare il problema del Vdroop basta settare la voce VCORE DROOP CONTROL su DISABLED Alimentatori Non compatibili Enermax Liberty 620w A quanto pare questa mobo non funziona con l'alimentatore enermax galaxy 1000, infatti al momento dell'accensione l'alimentatore va in protezione microcip said: il problema tra ali enermax e moba dfi sta nel fatto che le dfi per accendersi richiedono x nano secondo mentre gli ali enermax non riescono a sostenere questo intervallo e partono dopo x+1 nanosecondi. Chiunque sapesse di altre incompatibilità tra questa mobo e alimentatori me lo faccia sapere in modo da tenere aggiornato il thread Quote Link to comment Share on other sites More sharing options...
valego Posted August 22, 2007 Author Share Posted August 22, 2007 Un po' di foto del bios con i voltaggi massimi erogabili Nuove voci nel comparto DRAM timing con il bios 815 Quote Link to comment Share on other sites More sharing options...
principino1984 Posted August 22, 2007 Share Posted August 22, 2007 seguo seguo Quote Link to comment Share on other sites More sharing options...
megthebest Posted August 22, 2007 Share Posted August 22, 2007 ottima mobo vedo... Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted August 22, 2007 Share Posted August 22, 2007 Bravissimo Vale! Ciao;) Quote Link to comment Share on other sites More sharing options...
diablos Posted August 22, 2007 Share Posted August 22, 2007 vediamo che fa il giocattolino Quote Link to comment Share on other sites More sharing options...
hiwa Posted August 22, 2007 Share Posted August 22, 2007 eccomi:ROTFL::ROTFL: Quote Link to comment Share on other sites More sharing options...
principino1984 Posted August 23, 2007 Share Posted August 23, 2007 allora vale, la tiri o no questa maledetta mobo!! ma devo venire a prenderti per le orecchie? Quote Link to comment Share on other sites More sharing options...
MARCO74 Posted August 23, 2007 Share Posted August 23, 2007 mettila sotto phase,senti ma Vdroop si o no? se si quanto grazie ciao Quote Link to comment Share on other sites More sharing options...
microcip Posted August 23, 2007 Share Posted August 23, 2007 posso chiedere gentilmente un favore al possessore della main? Quote Link to comment Share on other sites More sharing options...
valego Posted August 23, 2007 Author Share Posted August 23, 2007 microcip said: posso chiedere gentilmente un favore al possessore della main? Chiedi se posso te lo faccio volentieri Per gli altri che vogliono i test dovranno aspettare che finisco di fare un paio di lavoretti e poi vado con i test Valerio Quote Link to comment Share on other sites More sharing options...
microcip Posted August 23, 2007 Share Posted August 23, 2007 mi faresti 2 piccoli test delle temperature? uno con la placca in rame e le heat esterne ed uno senza. mi fai partire hortos con priorità 10 e me lo lasci rullare anche per soli 15 minuti, screen e smonti. stesso discorso senza heat. naturalmente stesso procio e dissy(va bene pure il boxed). grazie mille:). ps:fai pure con calma vedi quando hai una oretta libera cosa riesci a combinare. Quote Link to comment Share on other sites More sharing options...
valego Posted August 23, 2007 Author Share Posted August 23, 2007 ok appena ho un po' di tempo provo a farlo, ma mi sa che devi aspettare nel week-end o inizio settimana prossima. Se magari prima che lo faccio io lo vuole fare un altro possessore della mobo (dj883u2 o hiwa) sono ben accetti Valerio Quote Link to comment Share on other sites More sharing options...
valego Posted August 23, 2007 Author Share Posted August 23, 2007 Uscito nuovo bios 815 Valerio Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted August 23, 2007 Share Posted August 23, 2007 valego said: Uscito nuovo bios 815 Valerio Molto bene!:n2mu: Ciao;) Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted August 23, 2007 Share Posted August 23, 2007 Spero di montare tutto entro domani! Uff...che casino col lavoro! Ciao;) Quote Link to comment Share on other sites More sharing options...
valego Posted August 23, 2007 Author Share Posted August 23, 2007 Invece io sono in apnea oggi stavo facendo qualche prova e ad un tratto il pc si spegne, il problema è che non si è più riavviato ora ho staccato il phase e ho visto che c'erano un paio di gocce d'acqua, ma non so se erano dovute a qualche falla nella coibentazione oppure al fatto che ho smontato mentre il tutto era ancora freddo. Cmq ho asciugato tutto con il phon, ora aspetto fino a domani e poi rimonto, oppure provo prima con un dissipatore. Speriamo bene Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted August 23, 2007 Share Posted August 23, 2007 valego said: Invece io sono in apnea oggi stavo facendo qualche prova e ad un tratto il pc si spegne, il problema è che non si è più riavviato ora ho staccato il phase e ho visto che c'erano un paio di gocce d'acqua, ma non so se erano dovute a qualche falla nella coibentazione oppure al fatto che ho smontato mentre il tutto era ancora freddo. Cmq ho asciugato tutto con il phon, ora aspetto fino a domani e poi rimonto, oppure provo prima con un dissipatore. Speriamo bene Porca miserai....perchè hai tolto quando era ancora freddo! Dai speriamo bene! Il nuovo bios va bene? Lo hai provato? Ciao;) Quote Link to comment Share on other sites More sharing options...
valego Posted August 23, 2007 Author Share Posted August 23, 2007 Non era sottozero, il termometro sull'evaporatore segnava 10° cmq poi ho subito asciugato con il phon. Il nuovo bios non ho fatto in tempo a provarlo :cry: La cosa che mi lascia perplesso è che, hai presente i numeri e lettere che appaiono sul display diagnostico, ecco ad un certo punto li non appariva più nulla, le ventole giravano ma per il resto zero. Ecco perchè poi ho smontato. Che ne pensi Anto? Valerio Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted August 23, 2007 Share Posted August 23, 2007 valego said: Non era sottozero, il termometro sull'evaporatore segnava 10° cmq poi ho subito asciugato con il phon. Il nuovo bios non ho fatto in tempo a provarlo :cry: La cosa che mi lascia perplesso è che, hai presente i numeri e lettere che appaiono sul display diagnostico, ecco ad un certo punto li non appariva più nulla, le ventole giravano ma per il resto zero. Ecco perchè poi ho smontato. Che ne pensi Anto? Valerio ....hai un'altro alimentatore da provare? Ciao;) Quote Link to comment Share on other sites More sharing options...
valego Posted August 23, 2007 Author Share Posted August 23, 2007 Ho quello sul "muletto", ma se devo smontarlo mi posso sparare perchè questa domanda? Pensi che sia l'ali? Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted August 23, 2007 Share Posted August 23, 2007 valego said: Ho quello sul "muletto", ma se devo smontarlo mi posso sparare perchè questa domanda? Pensi che sia l'ali? Perchè fatalità è lo steso problema che da a me con L'Enermax 1000. Io ho capito che non funzionava perchè L'Enermax dietro ha al lucetta che in base al problema ti dice la soluzione. Prova un nuovo ali, se neanche con quello va, alora sei sicuro che sia la scheda madre ad essere andata! Pazienza caro...io sono 8 giorni che ho la scheda è non l'ho provata un solo sevondo....:doppio:...non sai quanto mi rode! Ciao;) Quote Link to comment Share on other sites More sharing options...
valego Posted August 23, 2007 Author Share Posted August 23, 2007 Capisco, però questo problema avrebbe dovuto farmelo da subito, altrimenti non mi spiego il perchè prima ha funzionato e poi no :cheazz: boh cmq ora lo provo ad aria e vediamo Valerio Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.